Cubic Yard Calculator
This cubic yard calculator is a yardage calculator for any material: length × width × depth in feet, divided by 27. A 12 × 10 ft area at 3 in deep needs 1.11 cubic yards.
For uneven ground and spills.
You need
1.11cubic yards
- Cubic feet
- 30 ft³
- Cubic meters
- 0.85 m³
- Tandem loads (12 yd³)
- 1
A 12 ft × 10 ft area, 3 in deep, needs 1.11 cubic yards (30 cubic feet).
Estimate only — confirm quantities with your supplier before ordering.
More options: material weight and price
Use it for dirt, gravel, mulch, sand or any loose material you order by the yard. Along with cubic yards, the result gives cubic feet, cubic meters, tandem truckloads and, if you pick a material, the weight in tons.
All calculators
Volume & Conversions
Landscaping
- Dirt CalculatorFill dirt in yards, tons and truckloads.
- Topsoil CalculatorTopsoil for new lawns and leveling.
- Soil CalculatorSoil for raised beds, gardens and containers.
- Mulch CalculatorMulch in yards or bags, including tree rings.
- Gravel CalculatorGravel in yards and tons for drives and paths.
- Stone CalculatorRiver rock, limestone and landscape stone.
- Sand CalculatorPaver, fill and play sand in yards and bags.
- Sod CalculatorSod pieces, pallets and topsoil underneath.
Key facts
1 cubic yard = 27 cubic feet (3 ft × 3 ft × 3 ft).
One cubic yard covers 108 square feet at 3 inches deep and 324 square feet at 1 inch deep.
One cubic yard equals 0.765 cubic meters.
A cubic yard of dry, loose gravel weighs about 2,835 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.
A tandem-axle dump truck usually carries 12 or 14 cubic yards[src] Sources: Texas Department of Transportation.
How we calculate
Formula
Cubic feet = length (ft) × width (ft) × depth (in) ÷ 12
Cubic yards = cubic feet ÷ 27
Tons = cubic yards × weight (lb per yd³) ÷ 2,000
Assumptions and defaults
Every length is converted to feet first. Inches are divided by 12, yards are multiplied by 3 , and meters are divided by 0.3048.
Circles use π × radius². Triangles use base × height ÷ 2. Rings subtract the inner circle from the outer circle.
- The extra percentage is added to the volume before anything else. It starts at zero so you choose it.
Material weights are dry, loose figures from the U.S. Army earthmoving manual and a published weights table, listed in the sources below.
- Cubic yards and tons are rounded to two decimals. Truckloads always round up.
How to calculate cubic yards
To calculate cubic yards, multiply length × width × depth in feet, then divide by 27. That works for any flat-bottomed area, from a flower bed to a driveway. Here is the step-by-step version:
- Measure the length and width of the area in feet.
- Decide how deep the material needs to be, usually in inches.
- Divide the depth in inches by 12 to get feet.
- Multiply length × width × depth to get cubic feet.
- Divide cubic feet by 27 to get cubic yards.
- Add any extra you want for uneven ground and spills, then round up when you order.
Take a bed 20 feet long and 8 feet wide that needs 4 inches of soil. The depth is 0.33 feet, so the volume is 53.33 cubic feet. Divided by 27, that is 1.98 cubic yards.
How to figure cubic yards for a rectangle
A rectangle is the simplest case. Multiply the two sides to get square feet, multiply by the depth in feet, and divide by 27. If the sides are in yards, you can skip a step: square yards × depth in yards gives cubic yards directly. A space 4 yards by 3 yards filled 1 foot deep holds 4 cubic yards.
Circles and round beds
For a round area, measure straight across the middle to get the diameter. Half of that is the radius. Area = π × radius × radius. A round bed 10 feet across at 4 inches deep holds 26.18 cubic feet, or 0.97 cubic yards. Pick Circle in the calculator and enter the diameter.
Triangles and odd corners
A triangle covers half of the rectangle around it, so its area is base × height ÷ 2. Measure the base along one side and the height straight out from it at a right angle. A corner bed with a 10 foot base and 6 foot height at 6 inches deep needs 0.56 cubic yards.
Rings around trees
A ring is a circle with a hole in the middle, such as mulch around a tree trunk. Enter the outer diameter and the inner diameter, and the calculator subtracts the center. Use the inner diameter for the area you want to leave bare.
Irregular shapes
Break an odd shape into rectangles, circles and triangles, calculate each one, and add them together. For curved edges, measure a few widths along the length, average them, and treat the shape as a rectangle. Rounding a measurement up a little can save a second trip.
How to find cubic yards when depth is in inches
Most projects are measured in inches deep, so the key step is turning inches into feet. Divide inches by 12: 3 inches is 0.25 feet, and 6 inches is 0.5 feet. The table below does the math the other way round. It shows how far one cubic yard spreads at common depths.
| Depth (in) | Area covered by 1 yd³ (ft²) | Cubic yards per 100 ft² (yd³) |
|---|---|---|
| 1 | 324 | 0.31 |
| 2 | 162 | 0.62 |
| 3 | 108 | 0.93 |
| 4 | 81 | 1.23 |
| 6 | 54 | 1.85 |
| 12 | 27 | 3.7 |
To use it, divide your area by the coverage figure. A 300 square foot area at 3 inches deep needs 2.78 cubic yards.
How many yards do I need?
The number of yards you need is your area times your depth, divided by 27. The table shows cubic yards for common project sizes so you can sanity-check the calculator result before you call a supplier.
| Area | 2 in deep (yd³) | 3 in deep (yd³) | 4 in deep (yd³) | 6 in deep (yd³) |
|---|---|---|---|---|
| 10 × 10 ft (100 ft²) | 0.62 | 0.93 | 1.23 | 1.85 |
| 12 × 12 ft (144 ft²) | 0.89 | 1.33 | 1.78 | 2.67 |
| 10 × 20 ft (200 ft²) | 1.23 | 1.85 | 2.47 | 3.7 |
| 20 × 20 ft (400 ft²) | 2.47 | 3.7 | 4.94 | 7.41 |
| 20 × 30 ft (600 ft²) | 3.7 | 5.56 | 7.41 | 11.11 |
| 30 × 40 ft (1200 ft²) | 7.41 | 11.11 | 14.81 | 22.22 |
Cubic yards for common projects: worked examples
These worked examples use the same engine as the calculator, so you will get the same numbers if you type them in.
Garden bed refresh. A bed 24 feet by 4 feet at 3 inches deep: 24 cubic feet ÷ 27 = 0.89 cubic yards.
Gravel parking pad. A pad 20 feet by 10 feet at 4 inches deep: 66.67 cubic feet = 2.47 cubic yards. At the typical dry gravel weight, that is about 3.5 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.
Filling a low spot. An area 15 feet by 15 feet raised 6 inches: 112.5 cubic feet = 4.17 cubic yards. With dry fill dirt that weighs about 4.39 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.
What is a cubic yard?
A cubic yard is a cube 3 feet long, 3 feet wide and 3 feet deep, which is 27 cubic feet. For pictures and size comparisons, see the guide what is a cubic yard.
Common order sizes have their own pages with coverage, weight, bag and truckload tables: 2, 3, 4, 5, 10 and 20 cubic yards.
Cubic yards, cubic feet and cubic meters
Cubic yards are the ordering unit for bulk material, but bags are labeled in cubic feet and some plans use cubic meters. One cubic yard is 27 cubic feet, so divide cubic feet by 27 to get cubic yards. One cubic yard is 0.765 cubic meters, and one cubic meter is 1.31 cubic yards. The calculator shows all three units at once.
How much does a cubic yard weigh?
A cubic yard of dry, loose material weighs from about 0.92 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing for clay to 1.42 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing for gravel, and wet material weighs more. The figures below are for dry, loose material. They come from the U.S. Army earthmoving manual and a published weights table, and each typical figure sits inside the Army range.
| Material | Typical weight (lb/yd³) | Published range (lb/yd³) | Tons per yd³ (tons) |
|---|---|---|---|
| Fill dirt (earth, loam or silt)[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,106 | 1,900–2,200 | 1.05 |
| Sand[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,700 | 2,600–2,900 | 1.35 |
| Gravel[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,835 | 2,700–3,000 | 1.42 |
| Clay[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 1,836 | 1,700–2,000 | 0.92 |
Wet material weighs more. The Army manual lists wet sand at 2,800 to 3,100[src] Sources: Headquarters, Department of the Army pounds per cubic yard, compared with 2,600 to 2,900[src] Sources: Headquarters, Department of the Army pounds dry. To work out tons for your own volume, use the convert cubic yards to tons tool.
Loose vs compacted cubic yards
A cubic yard in the ground, a cubic yard loose in a truck and a cubic yard after compaction are not the same amount of material. Digging fluffs material up, and tamping or rolling packs it down. The U.S. Army earthmoving manual gives these average factors:
| Material | 1 yd³ in the ground → loose (yd³) | 1 loose yd³ → compacted (yd³) | 1 loose yd³ → in-ground (yd³) |
|---|---|---|---|
| Sand or gravel[src] Sources: Headquarters, Department of the Army | 1.11 | 0.86 | 0.9 |
| Loam (common earth)[src] Sources: Headquarters, Department of the Army | 1.25 | 0.72 | 0.8 |
| Clay[src] Sources: Headquarters, Department of the Army | 1.43 | 0.63 | 0.7 |
What this means for ordering: if you need a compacted layer, the loose material delivered will settle. For sand or gravel, one loose cubic yard compacts to about 0.86[src] Sources: Headquarters, Department of the Army cubic yard. For loam it is about 0.72[src] Sources: Headquarters, Department of the Army. Order enough loose material to end up with the compacted depth you need.
Bags vs bulk
Bags are handy for small jobs, but the count climbs fast. A cubic yard is 27 cubic feet, so divide 27 by the volume printed on the bag to see how many bags make one yard.
| Bag size (ft³) | Bags per yd³ (exact) | Bags to buy for 1 yd³ |
|---|---|---|
| 0.5 | 54 | 54 |
| 0.75 | 36 | 36 |
| 1 | 27 | 27 |
| 1.5 | 18 | 18 |
| 2 | 13.5 | 14 |
| 3 | 9 | 9 |
For example, 2 cubic yards in bags that each hold 2 cubic feet is 27 bags. Compare the bag price times the count with the bulk price per yard plus delivery. Each material calculator has a bag option that does this for you.
How many cubic yards fit in a dump truck?
Truck size sets how many trips a big job takes. The Texas Department of Transportation says single-axle trucks normally carry 6 cubic yards[src] Sources: Texas Department of Transportation of aggregate, and tandem-axle beds usually hold 12 or 14 cubic yards[src] Sources: Texas Department of Transportation. The Kentucky Transportation Cabinet lists tandem dump trucks in 8-10[src] Sources: Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) and 10-12[src] Sources: Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) yard classes. The calculator counts tandem loads at 12 cubic yards[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky). Ask your supplier how much they load per trip for your material. The guide how many yards fit in a dump truck goes into more detail.
Common mistakes when you calculate cubic yards
Depth in feet instead of inches
Typing 3 in a feet field when you meant inches gives a volume 12 times too big. Check the unit next to the depth before you trust the result.
- Forgetting compaction. Loose material settles. See the loose vs compacted table above.
- Measuring only one spot. Ground is rarely flat. Measure depth in several places and use the average.
- Mixing units. Feet times inches does not give cubic anything. Convert everything to feet first, or let the calculator do it.
- Ordering the exact number. Uneven ground and spills eat material. Use the extra field to add a margin you are comfortable with.
- Confusing square yards and cubic yards. A square yard is an area. A cubic yard is a volume.
A cubic yard calculator for every material
The cubic yard calculator above works for any loose material. For extra detail by material, such as bag counts, tons and typical depths, use a dedicated tool:
- Dirt calculator: a dirt volume calculator for fill dirt in yards, tons and truckloads.
- Topsoil calculator for new lawns and leveling.
- Mulch calculator with tree rings and bag counts.
- Gravel calculator for driveways and paths.
- Sand calculator for paver, fill and play sand.
- Concrete calculator for slabs, footings and post holes.
Think of this page as the material calculator that covers them all, and the others as shortcuts with the right defaults filled in.
Using metric units
Every length field takes feet, inches, yards, meters or centimeters, and you can mix them. A patio 3 meters by 2 meters at 10 centimeters deep holds 0.6 cubic meters, which is 0.78 cubic yards. The result card shows cubic meters next to cubic yards so you can order in either unit.